zuloopuzzle.blogg.se

1. #ADD CLOUD PRINTER SERIAL#
2. #ADD CLOUD PRINTER SOFTWARE#
3. #ADD CLOUD PRINTER CODE#
4. #ADD CLOUD PRINTER PASSWORD#

Paper Not TakenĪfter a ticket has been printed and cut, if the cut paper is not taken away, the alarm light on the printer will keep blinking. The value range that can be set is 10.0 ~ 100.0 mm.Ĭlick the “Black Mark Print Test” button to perform a black mark printing test. You cannot specify to start printing above the paper cutting position. “Print Position” specifies how many millimeters below the paper cutting position to start printing. The valid value ranges from -100.0 ~ 25.0 mm. Specify a negative value makes the cut position below the top of the black mark. “Cut Position” specifies the distance above the top of the black mark to cut paper in mm. After selecting “Paper with Black Mark”, set the position of black mark correctly according to the paper, and set the cutting position and printing position according to your application. “Paper with Black Mark” has small black blocks (the black marks) on both sides or in the middle of the paper at constant intervals. After selecting “Receipt”, you can choose whether to automatically feed a certain distance and cut the paper upon the cover is closed. “Receipt” is the most common thermal printing paper. Two types of printing paper are supported: “Receipt” and “Paper with Black Mark”. In the “Print Settings” page, you can set the default character set, print density and quality, paper layout, etc.Īfter making any changes to the settings, click “Save” button to apply.

#ADD CLOUD PRINTER SERIAL#

If the computer can’t match these settings, you can modify the printer’s serial port settings to meet the computer’s requirement.Īfter modifying the settings, click the “Save” button to apply.Ĭlick the “Print Test Page…” button to perform a print test via serial port.

The default serial port settings are: baud rate 115200, 8 data bits, 1 stop bit, no parity. The printer supports printing via serial port.

#ADD CLOUD PRINTER PASSWORD#

In the “Wi-Fi” page, click the “Configure SSID…” button to configure the SSID and password to connect the printer to the Wi-Fi network.Īfter connecting to the Wi-Fi network, click the “Refresh” button on the toolbar and you should see the allocated IP address.Ĭlick the “Print Test Page” button to perform a print test via Wi-Fi. In the “Wi-Fi” page, the dynamic and static IP addresses of the Wi-Fi interface are shown.Īfter modifying the static IP address and netmask, you must click the “Save” button to apply the changes.Ĭlick the “Print Test Page” button to perform a print test via Wi-Fi. Click the “Save” button and the “Restart…” button to apply the changes to the 4G module. In the “4G” page, the 4G network information is shown. Check the “Use Specific APN and Dial Number”, and set the APN and Dial Number correctly according to your local operator. Click the “Print Test Page” button to perform a print test via Ethernet. In the “Ethernet” page, the dynamic and static IP addresses of the Ethernet interface are shown:Īfter modifying the static IP address and netmask, you must click the “Save” button to apply the changes. This information is read only and can’t be modified.

#ADD CLOUD PRINTER SOFTWARE#

In the “Device Information” page, the printer model, serial number, software and hardware version number and other information is shown. Select the printer you want to connect to and click the “Connect” button. In the “Connection Type” column, the IP address of the printer is shown. If the printer does not appear in the list, please check whether the printer has been powered on, the USB cable has been connected correctly, or the printer has been connected to the same LAN as the computer, and then click the “Scan” button again to refresh the list. A dialog box will pop-up with the printers currently connected to the computer listed, as shown in the figure below: Run sunmi-cloud-printer-utility.exe, and then click the “Connect” button on the toolbar. Power on the printer and connect the printer to the computer with a type-C USB cable, or connect the printer to the same LAN (wireless or wired) as the computer. 5.Develop API for communication (method 2: Cloud to Cloud)ĭownload SUNMI Cloud Printer Utility Tools Connect to the Printerīefore setting up the printer with the printer utility, you need to connect to the printer first.4.Develop API for communication (method 1: Device to Cloud).3.Download the SDK for network configuration.

#ADD CLOUD PRINTER CODE#

Code Scanner Engine(Infrared scan code).